JUST HOW TO INSTALL A BATHTUB YOURSELF

Just How to Install a Bathtub Yourself

Just How to Install a Bathtub Yourself

Blog Article

Request A Quote

We have found this article pertaining to A Step-by-Step Guide to Installing a Bathtub listed below on the net and felt it made perfect sense to relate it with you here.


A Step-by-Step Guide to Installing a Bathtub
Mounting a bath tub isn't exactly rocket science, yet it does require solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old bathtub is readily easily accessible, the task can relocate quickly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually qualified yourself for the job as well as are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to think about utilizing one prior to you start. Possibilities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently gotten a brand-new bathtub and also do not require to alter the plan of your previous water system pipelines.
Your tools as well as material checklist ought to comprise the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you need to replace old faucets with new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain any water continuing to be in the system. The procedure of removing the existing faucets can be rather problematic as a result of the limited access that is often the instance.
    Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
    Before moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will certainly require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipes.
    If you require to fit a monobloc, then you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next off, position the tap in the placing hole in the bath/basin making sure that the washers are in area between the faucet and also the sink. Secure the faucet in position with the producer given backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap ports. The former kind ought to be linked to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.

    Installing the Tub


    Making use of the two wood boards under its feet, place the tub in the called for setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
    The next objective is to ensure that the tub is leveled all round. This can be attained by examining the spirit level as well as readjusting the feet on the bathtub until the level reviews degree.
    To install taps, fit all-time low of the outermost flexible tap port to the suitable supply pipeline by making a compression sign up with; then do the same for the other faucet.
    Activate the water supply as well as inspect all joints and also brand-new pipework for leaks and tighten them if required. Fill up the bath tub as well as also check the overflow outlet as well as the typical electrical outlet for leakages.
    Ultimately, fix the bath paneling as described in the producer's user's manual. Tiling as well as securing around the bath tub needs to wait up until the tub has actually been made use of at the very least when as this will certainly settle it into its last placement.

    Planning for the Installation


    Firstly, the supporting structure provided with the bathroom ought to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to avoid stress on the bathtub.
    Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
    Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last position.

    Tiling Around the Bath tub


    In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break a stiff seal, creating the water to permeate the wall in between the bathroom and the tiling, causing complications with moisture and possible leakages to the ceiling below.
    You can pick from a variety of coloured sealers to blend in your components and fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealer can crack fairly very early if you do not take into consideration this activity before sealing.
    Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly offered on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant sticky and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    Do you enjoy reading about How to Install a Bathtub? Leave a short review down the page. We would be delighted to listen to your feelings about this article. In hopes that you come back again soon. Be sure to take a moment to promote this post if you enjoyed it. We cherish reading our article about How to Install a Bathtub.




    Article


    Report this page